联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
耐热输送带保养方法
耐热输送带保养方法
Maintenance method of heat resistant conveyor belt
输送带在使用和保存中，应保持清洁避免阳光直射或雨雪浸淋,防止与酸、碱、油类、有机溶剂等物质接触，并距离发热装置一米以外。
In use and preservation, the conveyor belt should be kept clean to avoid direct sunlight or rain and snow leaching, and prevent contact with acid, alkali, oil, organic solvent and other substances, and one meter away from the heating device.
保存时仓库温度宜保持在18-40 ℃之间，相对湿度宜保持在 50- 80 %之间。
The storage temperature should be kept at 18-40 C and the relative humidity should be maintained at 50-80.
保存期间，输送带须成卷放置，不得折叠，放置期间应每季翻动一次。
During storage, the conveyor belt must be placed in rolls, not folded, and should be rolled once every season during placement.
不同类型、规格层数的输送带不宜接在一起使用，其接头最好采用胶接法。
The conveyor belts of different types and specifications should not be used together, and the joints should be glued.
输送带的类型、结构、规格、层数应根据使用条件合理选用。
The type, structure, specification and number of layers should be selected according to the use conditions.
输送带运行速度一般不宜大于 2 .5 米/秒，块度大，磨损性大的物料和使用固定的卸料装置应尽量采用低速。
The running speed of conveyor belts should not be greater than 2.5 m / s. generally, the material with large block size and high wear resistance should be used as low as possible.
输送机的传动滚筒直径与输送带布层的关系、传动滚筒、改向滚筒的配套以及对托辊槽角的要求应根据输送机的设计规定，合理选取。
The relationship between the diameter of the transmission roller and the layer of the conveyer belt, the matching of the driving roller, the reformed roller, and the demand for the angle of the roller should be selected according to the design rules of the conveyor.
给料方向应顺输送带的运行方向，为减小物料下落时对输送带的冲击应采溜槽，减小物料下落距离；输送带受料段应缩短托辊间距和采用缓冲托辊为漏料，带顺应采用柔软适度的挡料板，以免档料板过硬，刮破输送带的带面。
The direction of feeding should be followed by the running direction of the conveyor belt. In order to reduce the impact of the material on the conveyor belt, the chute should be mined and the drop distance of the material should be reduced. The conveyer belt should shorten the spacing of the roller and use the cushioning roller as the leaky material. The belt should adapt to the soft and moderate baffle plate, so as to avoid the strip surface of the conveyor belt.
Maintenance method of heat resistant conveyor belt
输送带在使用和保存中，应保持清洁避免阳光直射或雨雪浸淋,防止与酸、碱、油类、有机溶剂等物质接触，并距离发热装置一米以外。
In use and preservation, the conveyor belt should be kept clean to avoid direct sunlight or rain and snow leaching, and prevent contact with acid, alkali, oil, organic solvent and other substances, and one meter away from the heating device.
保存时仓库温度宜保持在18-40 ℃之间，相对湿度宜保持在 50- 80 %之间。
The storage temperature should be kept at 18-40 C and the relative humidity should be maintained at 50-80.
保存期间，输送带须成卷放置，不得折叠，放置期间应每季翻动一次。
During storage, the conveyor belt must be placed in rolls, not folded, and should be rolled once every season during placement.
不同类型、规格层数的输送带不宜接在一起使用，其接头最好采用胶接法。
The conveyor belts of different types and specifications should not be used together, and the joints should be glued.
输送带的类型、结构、规格、层数应根据使用条件合理选用。
The type, structure, specification and number of layers should be selected according to the use conditions.
输送带运行速度一般不宜大于 2 .5 米/秒，块度大，磨损性大的物料和使用固定的卸料装置应尽量采用低速。
The running speed of conveyor belts should not be greater than 2.5 m / s. generally, the material with large block size and high wear resistance should be used as low as possible.
输送机的传动滚筒直径与输送带布层的关系、传动滚筒、改向滚筒的配套以及对托辊槽角的要求应根据输送机的设计规定，合理选取。
The relationship between the diameter of the transmission roller and the layer of the conveyer belt, the matching of the driving roller, the reformed roller, and the demand for the angle of the roller should be selected according to the design rules of the conveyor.
给料方向应顺输送带的运行方向，为减小物料下落时对输送带的冲击应采溜槽，减小物料下落距离；输送带受料段应缩短托辊间距和采用缓冲托辊为漏料，带顺应采用柔软适度的挡料板，以免档料板过硬，刮破输送带的带面。
The direction of feeding should be followed by the running direction of the conveyor belt. In order to reduce the impact of the material on the conveyor belt, the chute should be mined and the drop distance of the material should be reduced. The conveyer belt should shorten the spacing of the roller and use the cushioning roller as the leaky material. The belt should adapt to the soft and moderate baffle plate, so as to avoid the strip surface of the conveyor belt.
