1、输送胶带在运输和贮存中，应保持清洁避免阳光直射或雨雪浸淋,防止与酸、碱、油类、有 机溶剂等物质接触，并距离发热装置一米以外。
1. In transportation and storage, conveyor belts should be kept clean to avoid direct sunlight or rain and snow leaching, to prevent contact with acids, alkalis, oils, organic solvents and other substances, and one meter away from the heating device.
2、贮存时仓库温度宜保持一 18-40 ℃之间，相对湿度宜保持在 50- 80 %之间。
2. Warehouse temperature and relative humidity should be kept between 18-40 C and 50-80% during storage.
3 、贮存期间，产品须成卷放置，不得折迭，放置期间应每季翻动 一次。
3. During storage, the products should be placed in rolls and not folded. During storage, the products should be flipped once a quarter.
4 、不同类型、规格层数的输送带不宜接在一起使用，其接头最好采用胶接法。
4. Conveyor belts of different types and layers of specifications are not suitable to be joined together. It is better to use gluing method for their joints.
5 、输送胶带的类型、结构、规格、层数应根据使用条件合理选用。
5. The type, structure, specifications and layers of conveying belt should be selected reasonably according to the use conditions.
6 、输送胶带运行速度一般不宜大于 2 ． 5 米/秒，块度大，磨损性大的物料和使用固定梨的 卸料装置应尽量采用低速。
6. Conveyor Belt should not run faster than 2.5 m/s. Materials with large fragmentation and abrasion and unloading device of fixed pear should be used as low as possible.
7 、运输机的传动滚筒直径与输送带布层的关系、传动滚筒、改向滚筒的配套以及对 托辊槽角 的要求应根据运输机的设计规定，合理选取。
7. The relationship between the diameter of the driving drum and the layers of the conveyor belt, the matching of the driving drum and the reversing drum, and the requirement of the groove angle of the idler should be reasonably selected according to the design regulations of the conveyor.
8 、给料方向应顺胶带的运行方向，为减小物料下落时对胶带的冲击应采溜槽，减小物料下落距 离；胶带受料段应缩短托辊间距和采用缓冲托辊为漏料，带顺应采用柔软适度的挡料板，以免 档料板过硬，刮破输送带的带面。
8. The feeding direction should follow the running direction of the belt. In order to reduce the impact on the belt when the material falls, the chute should be adopted to reduce the falling distance of the material. The belt receiving section should shorten the distance between the idlers and adopt the buffer idler as the leak material, and the belt should adopt a soft and moderate baffle to avoid the baffle being too hard and scraping the belt surface.
9 、输送带在使用中应注意以下事项： ①避免托辊被物料覆盖，造成回转不灵，防止漏料卡于滚筒与胶带之间，注意活动部分的润滑， 但不得油污输送胶带； ②避免带负荷启动； ③胶带发生跑偏，应用时采取措施纠正； ④发现胶带局部损人造棉应用时修补，以免扩大；
9. Attention should be paid to the following matters in the use of conveyor belts: 1. Avoiding the roller from being covered by materials, causing rotation failure, preventing material leakage from sticking between the drum and the belt, paying attention to lubrication of the moving part, but not oil-stained conveyor belt; 2. Avoiding the start of belt load; 3. Taking measures to correct the deviation of the belt in application; 4. Repairing the partial damage of the belt in the application of artificial cotton, so as to avoid it. Expand;